diff --git a/arch/arm/mach-at91/arm926ejs/at91sam9260_devices.c b/arch/arm/mach-at91/arm926ejs/at91sam9260_devices.c
index 9d78719..c10571f 100644
--- a/arch/arm/mach-at91/arm926ejs/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/arm926ejs/at91sam9260_devices.c
@@ -219,7 +219,7 @@
 	{ ATMEL_BASE_PIOC, "PC" },
 };
 
-U_BOOT_DEVICES(at91sam9260_gpios) = {
+U_BOOT_DRVINFOS(at91sam9260_gpios) = {
 	{ "atmel_at91rm9200_gpio", &at91sam9260_plat[0] },
 	{ "atmel_at91rm9200_gpio", &at91sam9260_plat[1] },
 	{ "atmel_at91rm9200_gpio", &at91sam9260_plat[2] },
diff --git a/arch/arm/mach-at91/arm926ejs/at91sam9m10g45_devices.c b/arch/arm/mach-at91/arm926ejs/at91sam9m10g45_devices.c
index f503553..d517810 100644
--- a/arch/arm/mach-at91/arm926ejs/at91sam9m10g45_devices.c
+++ b/arch/arm/mach-at91/arm926ejs/at91sam9m10g45_devices.c
@@ -175,7 +175,7 @@
 	{ ATMEL_BASE_PIOE, "PE" },
 };
 
-U_BOOT_DEVICES(at91sam9260_gpios) = {
+U_BOOT_DRVINFOS(at91sam9260_gpios) = {
 	{ "atmel_at91rm9200_gpio", &at91sam9260_plat[0] },
 	{ "atmel_at91rm9200_gpio", &at91sam9260_plat[1] },
 	{ "atmel_at91rm9200_gpio", &at91sam9260_plat[2] },
diff --git a/arch/arm/mach-imx/mx6/soc.c b/arch/arm/mach-imx/mx6/soc.c
index 1649f6d..bf6dddf 100644
--- a/arch/arm/mach-imx/mx6/soc.c
+++ b/arch/arm/mach-imx/mx6/soc.c
@@ -44,7 +44,7 @@
 	.fuse_word = 6,
 };
 
-U_BOOT_DEVICE(imx6_thermal) = {
+U_BOOT_DRVINFO(imx6_thermal) = {
 	.name = "imx_thermal",
 	.plat = &imx6_thermal_plat,
 };
diff --git a/arch/arm/mach-imx/mx7/soc.c b/arch/arm/mach-imx/mx7/soc.c
index 1359399..fda25ba 100644
--- a/arch/arm/mach-imx/mx7/soc.c
+++ b/arch/arm/mach-imx/mx7/soc.c
@@ -60,7 +60,7 @@
 	.fuse_word = 3,
 };
 
-U_BOOT_DEVICE(imx7_thermal) = {
+U_BOOT_DRVINFO(imx7_thermal) = {
 	.name = "imx_thermal",
 	.plat = &imx7_thermal_plat,
 };
diff --git a/arch/arm/mach-lpc32xx/devices.c b/arch/arm/mach-lpc32xx/devices.c
index 04e026a..e1e2e0d 100644
--- a/arch/arm/mach-lpc32xx/devices.c
+++ b/arch/arm/mach-lpc32xx/devices.c
@@ -62,7 +62,7 @@
 };
 #endif
 
-U_BOOT_DEVICES(lpc32xx_uarts) = {
+U_BOOT_DRVINFOS(lpc32xx_uarts) = {
 #if defined(CONFIG_LPC32XX_HSUART)
 	{ "lpc32xx_hsuart", &lpc32xx_hsuart[0], },
 	{ "lpc32xx_hsuart", &lpc32xx_hsuart[1], },
@@ -124,7 +124,7 @@
 	writel(ctrl, &clk->i2cclk_ctrl);
 }
 
-U_BOOT_DEVICE(lpc32xx_gpios) = {
+U_BOOT_DRVINFO(lpc32xx_gpios) = {
 	.name = "gpio_lpc32xx"
 };
 
diff --git a/arch/arm/mach-omap2/am33xx/board.c b/arch/arm/mach-omap2/am33xx/board.c
index b5f2b75..e17898d 100644
--- a/arch/arm/mach-omap2/am33xx/board.c
+++ b/arch/arm/mach-omap2/am33xx/board.c
@@ -99,7 +99,7 @@
 # endif
 };
 
-U_BOOT_DEVICES(am33xx_uarts) = {
+U_BOOT_DRVINFOS(am33xx_uarts) = {
 	{ "ns16550_serial", &am33xx_serial[0] },
 #  ifdef CONFIG_SYS_NS16550_COM2
 	{ "ns16550_serial", &am33xx_serial[1] },
@@ -119,7 +119,7 @@
 	{ I2C_BASE3, 100000, OMAP_I2C_REV_V2},
 };
 
-U_BOOT_DEVICES(am33xx_i2c) = {
+U_BOOT_DRVINFOS(am33xx_i2c) = {
 	{ "i2c_omap", &am33xx_i2c[0] },
 	{ "i2c_omap", &am33xx_i2c[1] },
 	{ "i2c_omap", &am33xx_i2c[2] },
@@ -138,7 +138,7 @@
 #endif
 };
 
-U_BOOT_DEVICES(am33xx_gpios) = {
+U_BOOT_DRVINFOS(am33xx_gpios) = {
 	{ "gpio_omap", &am33xx_gpio[0] },
 	{ "gpio_omap", &am33xx_gpio[1] },
 	{ "gpio_omap", &am33xx_gpio[2] },
@@ -155,7 +155,7 @@
 	.pin_dir = MCSPI_PINDIR_D0_IN_D1_OUT,
 };
 
-U_BOOT_DEVICE(am33xx_spi) = {
+U_BOOT_DRVINFO(am33xx_spi) = {
 	.name = "omap3_spi",
 	.plat = &omap3_spi_pdata,
 };
@@ -234,7 +234,7 @@
 		},
 };
 
-U_BOOT_DEVICES(am33xx_usbs) = {
+U_BOOT_DRVINFOS(am33xx_usbs) = {
 #if CONFIG_AM335X_USB0_MODE == MUSB_PERIPHERAL
 	{ "ti-musb-peripheral", &usb0 },
 #elif CONFIG_AM335X_USB0_MODE == MUSB_HOST
diff --git a/arch/arm/mach-omap2/omap3/board.c b/arch/arm/mach-omap2/omap3/board.c
index 6ffedd1..4da8df4 100644
--- a/arch/arm/mach-omap2/omap3/board.c
+++ b/arch/arm/mach-omap2/omap3/board.c
@@ -47,7 +47,7 @@
 	{ 5, OMAP34XX_GPIO6_BASE },
 };
 
-U_BOOT_DEVICES(omap34xx_gpios) = {
+U_BOOT_DRVINFOS(omap34xx_gpios) = {
 	{ "gpio_omap", &omap34xx_gpio[0] },
 	{ "gpio_omap", &omap34xx_gpio[1] },
 	{ "gpio_omap", &omap34xx_gpio[2] },
diff --git a/arch/arm/mach-tegra/board.c b/arch/arm/mach-tegra/board.c
index bf01aa5..9de9836 100644
--- a/arch/arm/mach-tegra/board.c
+++ b/arch/arm/mach-tegra/board.c
@@ -264,7 +264,7 @@
 	.fcr = UART_FCR_DEFVAL,
 };
 
-U_BOOT_DEVICE(ns16550_com1) = {
+U_BOOT_DRVINFO(ns16550_com1) = {
 	"ns16550_serial", &ns16550_com1_pdata
 };
 #endif
diff --git a/arch/arm/mach-tegra/board2.c b/arch/arm/mach-tegra/board2.c
index 48c4f32..8569ad7 100644
--- a/arch/arm/mach-tegra/board2.c
+++ b/arch/arm/mach-tegra/board2.c
@@ -42,7 +42,7 @@
 
 #ifdef CONFIG_SPL_BUILD
 /* TODO(sjg@chromium.org): Remove once SPL supports device tree */
-U_BOOT_DEVICE(tegra_gpios) = {
+U_BOOT_DRVINFO(tegra_gpios) = {
 	"gpio_tegra"
 };
 #endif
diff --git a/board/armltd/integrator/integrator.c b/board/armltd/integrator/integrator.c
index 21bea62..3c56fa1 100644
--- a/board/armltd/integrator/integrator.c
+++ b/board/armltd/integrator/integrator.c
@@ -43,7 +43,7 @@
 #endif
 };
 
-U_BOOT_DEVICE(integrator_serials) = {
+U_BOOT_DRVINFO(integrator_serials) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/armltd/total_compute/total_compute.c b/board/armltd/total_compute/total_compute.c
index 6263d0c..da24b32 100644
--- a/board/armltd/total_compute/total_compute.c
+++ b/board/armltd/total_compute/total_compute.c
@@ -15,7 +15,7 @@
 	.clock = CONFIG_PL011_CLOCK,
 };
 
-U_BOOT_DEVICE(total_compute_serials) = {
+U_BOOT_DRVINFO(total_compute_serials) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/armltd/vexpress64/vexpress64.c b/board/armltd/vexpress64/vexpress64.c
index 6df6bcd..bd66d52 100644
--- a/board/armltd/vexpress64/vexpress64.c
+++ b/board/armltd/vexpress64/vexpress64.c
@@ -26,7 +26,7 @@
 	.clock = CONFIG_PL011_CLOCK,
 };
 
-U_BOOT_DEVICE(vexpress_serials) = {
+U_BOOT_DRVINFO(vexpress_serials) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/bluewater/gurnard/gurnard.c b/board/bluewater/gurnard/gurnard.c
index a71b4eb..17ecdb6 100644
--- a/board/bluewater/gurnard/gurnard.c
+++ b/board/bluewater/gurnard/gurnard.c
@@ -420,7 +420,7 @@
 	.base_addr = ATMEL_BASE_DBGU,
 };
 
-U_BOOT_DEVICE(at91sam9260_serial) = {
+U_BOOT_DRVINFO(at91sam9260_serial) = {
 	.name	= "serial_atmel",
 	.plat = &at91sam9260_serial_plat,
 };
diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c
index 9e41a42..58fab15 100644
--- a/board/bluewater/snapper9260/snapper9260.c
+++ b/board/bluewater/snapper9260/snapper9260.c
@@ -147,7 +147,7 @@
 	.base_addr = ATMEL_BASE_DBGU,
 };
 
-U_BOOT_DEVICE(at91sam9260_serial) = {
+U_BOOT_DRVINFO(at91sam9260_serial) = {
 	.name	= "serial_atmel",
 	.plat = &at91sam9260_serial_plat,
 };
diff --git a/board/cadence/xtfpga/xtfpga.c b/board/cadence/xtfpga/xtfpga.c
index 29db51b..c26793d 100644
--- a/board/cadence/xtfpga/xtfpga.c
+++ b/board/cadence/xtfpga/xtfpga.c
@@ -93,7 +93,7 @@
 	return 0;
 }
 
-U_BOOT_DEVICE(sysreset) = {
+U_BOOT_DRVINFO(sysreset) = {
 	.name = "xtfpga_sysreset",
 };
 
@@ -104,7 +104,7 @@
 	.packet_base = CONFIG_SYS_ETHOC_BUFFER_ADDR,
 };
 
-U_BOOT_DEVICE(ethoc) = {
+U_BOOT_DRVINFO(ethoc) = {
 	.name = "ethoc",
 	.plat = &ethoc_pdata,
 };
diff --git a/board/cavium/thunderx/thunderx.c b/board/cavium/thunderx/thunderx.c
index 22c4c72..fd23472 100644
--- a/board/cavium/thunderx/thunderx.c
+++ b/board/cavium/thunderx/thunderx.c
@@ -25,7 +25,7 @@
 	.skip_init = true,
 };
 
-U_BOOT_DEVICE(thunderx_serial0) = {
+U_BOOT_DRVINFO(thunderx_serial0) = {
 	.name = "serial_pl01x",
 	.plat = &serial0,
 };
@@ -37,7 +37,7 @@
 	.skip_init = true,
 };
 
-U_BOOT_DEVICE(thunderx_serial1) = {
+U_BOOT_DRVINFO(thunderx_serial1) = {
 	.name = "serial_pl01x",
 	.plat = &serial1,
 };
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index bc3ce4d..7520e96 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -728,7 +728,7 @@
 	.reg = (struct mxc_uart *)UART4_BASE,
 };
 
-U_BOOT_DEVICE(cm_fx6_serial) = {
+U_BOOT_DRVINFO(cm_fx6_serial) = {
 	.name	= "serial_mxc",
 	.plat = &cm_fx6_mxc_serial_plat,
 };
diff --git a/board/davinci/da8xxevm/omapl138_lcdk.c b/board/davinci/da8xxevm/omapl138_lcdk.c
index a8ece17..a088585 100644
--- a/board/davinci/da8xxevm/omapl138_lcdk.c
+++ b/board/davinci/da8xxevm/omapl138_lcdk.c
@@ -363,7 +363,7 @@
 	.fcr = UART_FCR_DEFVAL,
 };
 
-U_BOOT_DEVICE(omapl138_uart) = {
+U_BOOT_DRVINFO(omapl138_uart) = {
 	.name = "ns16550_serial",
 	.plat = &serial_pdata,
 };
@@ -379,7 +379,7 @@
 		.name = "da830-mmc",
 	},
 };
-U_BOOT_DEVICE(omapl138_mmc) = {
+U_BOOT_DRVINFO(omapl138_mmc) = {
 	.name = "ti_da830_mmc",
 	.plat = &mmc_plat,
 };
diff --git a/board/freescale/ls1012afrdm/eth.c b/board/freescale/ls1012afrdm/eth.c
index 85104ab..d2df935 100644
--- a/board/freescale/ls1012afrdm/eth.c
+++ b/board/freescale/ls1012afrdm/eth.c
@@ -114,12 +114,12 @@
 	},
 };
 
-U_BOOT_DEVICE(ls1012a_pfe0) = {
+U_BOOT_DRVINFO(ls1012a_pfe0) = {
 	.name = "pfe_eth",
 	.plat = &pfe_pdata0,
 };
 
-U_BOOT_DEVICE(ls1012a_pfe1) = {
+U_BOOT_DRVINFO(ls1012a_pfe1) = {
 	.name = "pfe_eth",
 	.plat = &pfe_pdata1,
 };
diff --git a/board/freescale/ls1012aqds/eth.c b/board/freescale/ls1012aqds/eth.c
index f6f43d2..8189f41 100644
--- a/board/freescale/ls1012aqds/eth.c
+++ b/board/freescale/ls1012aqds/eth.c
@@ -298,12 +298,12 @@
 	},
 };
 
-U_BOOT_DEVICE(ls1012a_pfe0) = {
+U_BOOT_DRVINFO(ls1012a_pfe0) = {
 	.name = "pfe_eth",
 	.plat = &pfe_pdata0,
 };
 
-U_BOOT_DEVICE(ls1012a_pfe1) = {
+U_BOOT_DRVINFO(ls1012a_pfe1) = {
 	.name = "pfe_eth",
 	.plat = &pfe_pdata1,
 };
diff --git a/board/freescale/ls1012ardb/eth.c b/board/freescale/ls1012ardb/eth.c
index 5e923e5..2241d06 100644
--- a/board/freescale/ls1012ardb/eth.c
+++ b/board/freescale/ls1012ardb/eth.c
@@ -160,12 +160,12 @@
 	},
 };
 
-U_BOOT_DEVICE(ls1012a_pfe0) = {
+U_BOOT_DRVINFO(ls1012a_pfe0) = {
 	.name = "pfe_eth",
 	.plat = &pfe_pdata0,
 };
 
-U_BOOT_DEVICE(ls1012a_pfe1) = {
+U_BOOT_DRVINFO(ls1012a_pfe1) = {
 	.name = "pfe_eth",
 	.plat = &pfe_pdata1,
 };
diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c
index 8d0115e..70dd34e 100644
--- a/board/freescale/lx2160a/lx2160a.c
+++ b/board/freescale/lx2160a/lx2160a.c
@@ -62,7 +62,7 @@
 	.type = TYPE_PL011,
 };
 
-U_BOOT_DEVICE(nxp_serial0) = {
+U_BOOT_DRVINFO(nxp_serial0) = {
 	.name = "serial_pl01x",
 	.plat = &serial0,
 };
@@ -72,7 +72,7 @@
 	.type = TYPE_PL011,
 };
 
-U_BOOT_DEVICE(nxp_serial1) = {
+U_BOOT_DRVINFO(nxp_serial1) = {
 	.name = "serial_pl01x",
 	.plat = &serial1,
 };
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index c7224d1..048f624 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -1375,7 +1375,7 @@
 	.reg = (struct mxc_uart *)UART2_BASE,
 };
 
-U_BOOT_DEVICE(ventana_serial) = {
+U_BOOT_DRVINFO(ventana_serial) = {
 	.name   = "serial_mxc",
 	.plat = &ventana_mxc_serial_plat,
 };
diff --git a/board/hisilicon/hikey/hikey.c b/board/hisilicon/hikey/hikey.c
index 0ac8830..65a8179 100644
--- a/board/hisilicon/hikey/hikey.c
+++ b/board/hisilicon/hikey/hikey.c
@@ -50,7 +50,7 @@
 
 };
 
-U_BOOT_DEVICES(hi6220_gpios) = {
+U_BOOT_DRVINFOS(hi6220_gpios) = {
 	{ "gpio_hi6220", &hi6220_gpio[0] },
 	{ "gpio_hi6220", &hi6220_gpio[1] },
 	{ "gpio_hi6220", &hi6220_gpio[2] },
@@ -89,7 +89,7 @@
 	.clock = 19200000
 };
 
-U_BOOT_DEVICE(hikey_seriala) = {
+U_BOOT_DRVINFO(hikey_seriala) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/hisilicon/hikey960/hikey960.c b/board/hisilicon/hikey960/hikey960.c
index 04b8cde..3fe4c60 100644
--- a/board/hisilicon/hikey960/hikey960.c
+++ b/board/hisilicon/hikey960/hikey960.c
@@ -32,7 +32,7 @@
 	.clock = 19200000
 };
 
-U_BOOT_DEVICE(hikey960_serial0) = {
+U_BOOT_DRVINFO(hikey960_serial0) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/hisilicon/poplar/poplar.c b/board/hisilicon/poplar/poplar.c
index b8be4ce..bfb2c66 100644
--- a/board/hisilicon/poplar/poplar.c
+++ b/board/hisilicon/poplar/poplar.c
@@ -46,7 +46,7 @@
 	.clock = 75000000,
 };
 
-U_BOOT_DEVICE(poplar_serial) = {
+U_BOOT_DRVINFO(poplar_serial) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/isee/igep00x0/igep00x0.c b/board/isee/igep00x0/igep00x0.c
index 6a7da50..0932f62 100644
--- a/board/isee/igep00x0/igep00x0.c
+++ b/board/isee/igep00x0/igep00x0.c
@@ -36,7 +36,7 @@
 	.fcr = UART_FCR_DEFVAL,
 };
 
-U_BOOT_DEVICE(igep_uart) = {
+U_BOOT_DRVINFO(igep_uart) = {
 	"ns16550_serial",
 	&igep_serial
 };
diff --git a/board/lg/sniper/sniper.c b/board/lg/sniper/sniper.c
index d11630b..118ab26 100644
--- a/board/lg/sniper/sniper.c
+++ b/board/lg/sniper/sniper.c
@@ -37,7 +37,7 @@
 	.fcr = UART_FCR_DEFVAL,
 };
 
-U_BOOT_DEVICE(sniper_serial) = {
+U_BOOT_DRVINFO(sniper_serial) = {
 	.name = "ns16550_serial",
 	.plat = &serial_omap_plat
 };
diff --git a/board/nokia/rx51/rx51.c b/board/nokia/rx51/rx51.c
index bafb620..253ee3c 100644
--- a/board/nokia/rx51/rx51.c
+++ b/board/nokia/rx51/rx51.c
@@ -709,7 +709,7 @@
 	{ I2C_BASE3, 400000, OMAP_I2C_REV_V1 },
 };
 
-U_BOOT_DEVICES(rx51_i2c) = {
+U_BOOT_DRVINFOS(rx51_i2c) = {
 	{ "i2c_omap", &rx51_i2c[0] },
 	{ "i2c_omap", &rx51_i2c[1] },
 	{ "i2c_omap", &rx51_i2c[2] },
diff --git a/board/sandbox/sandbox.c b/board/sandbox/sandbox.c
index 3235541..d152703 100644
--- a/board/sandbox/sandbox.c
+++ b/board/sandbox/sandbox.c
@@ -23,7 +23,7 @@
 
 #if !CONFIG_IS_ENABLED(OF_PLATDATA)
 /* Add a simple GPIO device */
-U_BOOT_DEVICE(gpio_sandbox) = {
+U_BOOT_DRVINFO(gpio_sandbox) = {
 	.name = "sandbox_gpio",
 };
 #endif
diff --git a/board/siemens/corvus/board.c b/board/siemens/corvus/board.c
index 1613c44..25d85a8 100644
--- a/board/siemens/corvus/board.c
+++ b/board/siemens/corvus/board.c
@@ -318,7 +318,7 @@
 	.base_addr = ATMEL_BASE_DBGU,
 };
 
-U_BOOT_DEVICE(at91sam9260_serial) = {
+U_BOOT_DRVINFO(at91sam9260_serial) = {
 	.name	= "serial_atmel",
 	.plat = &at91sam9260_serial_plat,
 };
diff --git a/board/st/stv0991/stv0991.c b/board/st/stv0991/stv0991.c
index 3371973..95e203f 100644
--- a/board/st/stv0991/stv0991.c
+++ b/board/st/stv0991/stv0991.c
@@ -30,7 +30,7 @@
 	.clock = 2700 * 1000,
 };
 
-U_BOOT_DEVICE(stv09911_serials) = {
+U_BOOT_DRVINFO(stv09911_serials) = {
 	.name = "serial_pl01x",
 	.plat = &serial_plat,
 };
diff --git a/board/sysam/amcore/amcore.c b/board/sysam/amcore/amcore.c
index 42e1a80..65fc60e 100644
--- a/board/sysam/amcore/amcore.c
+++ b/board/sysam/amcore/amcore.c
@@ -113,7 +113,7 @@
 	.baudrate = CONFIG_BAUDRATE,
 };
 
-U_BOOT_DEVICE(coldfire_serial) = {
+U_BOOT_DRVINFO(coldfire_serial) = {
 	.name = "serial_coldfire",
 	.plat = &mcf5307_serial_plat,
 };
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 2aa385a..40d2e02 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -927,7 +927,7 @@
 	.priv_pdata = &am335_eth_data,
 };
 
-U_BOOT_DEVICE(am335x_eth) = {
+U_BOOT_DRVINFO(am335x_eth) = {
 	.name = "eth_cpsw",
 	.plat = &cpsw_pdata,
 };
@@ -972,7 +972,7 @@
 	.cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
 };
 
-U_BOOT_DEVICE(am335x_mmc0) = {
+U_BOOT_DRVINFO(am335x_mmc0) = {
 	.name = "omap_hsmmc",
 	.plat = &am335x_mmc0_plat,
 };
@@ -986,7 +986,7 @@
 	.cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
 };
 
-U_BOOT_DEVICE(am335x_mmc1) = {
+U_BOOT_DRVINFO(am335x_mmc1) = {
 	.name = "omap_hsmmc",
 	.plat = &am335x_mmc1_plat,
 };
diff --git a/board/timll/devkit8000/devkit8000.c b/board/timll/devkit8000/devkit8000.c
index 8753836..0731fb7 100644
--- a/board/timll/devkit8000/devkit8000.c
+++ b/board/timll/devkit8000/devkit8000.c
@@ -54,7 +54,7 @@
 	.fcr = UART_FCR_DEFVAL,
 };
 
-U_BOOT_DEVICE(devkit8000_uart) = {
+U_BOOT_DRVINFO(devkit8000_uart) = {
 	"ns16550_serial",
 	&devkit8000_serial
 };
diff --git a/board/toradex/apalis_imx6/apalis_imx6.c b/board/toradex/apalis_imx6/apalis_imx6.c
index 362a750..5ae5274 100644
--- a/board/toradex/apalis_imx6/apalis_imx6.c
+++ b/board/toradex/apalis_imx6/apalis_imx6.c
@@ -1149,7 +1149,7 @@
 	.use_dte = true,
 };
 
-U_BOOT_DEVICE(mxc_serial) = {
+U_BOOT_DRVINFO(mxc_serial) = {
 	.name = "serial_mxc",
 	.plat = &mxc_serial_plat,
 };
diff --git a/board/toradex/colibri-imx6ull/colibri-imx6ull.c b/board/toradex/colibri-imx6ull/colibri-imx6ull.c
index 056064f..6ff55ce 100644
--- a/board/toradex/colibri-imx6ull/colibri-imx6ull.c
+++ b/board/toradex/colibri-imx6ull/colibri-imx6ull.c
@@ -208,7 +208,7 @@
 	.use_dte = 1,
 };
 
-U_BOOT_DEVICE(mxc_serial) = {
+U_BOOT_DRVINFO(mxc_serial) = {
 	.name = "serial_mxc",
 	.plat = &mxc_serial_plat,
 };
diff --git a/board/toradex/colibri_imx6/colibri_imx6.c b/board/toradex/colibri_imx6/colibri_imx6.c
index a82daad..57d3e52 100644
--- a/board/toradex/colibri_imx6/colibri_imx6.c
+++ b/board/toradex/colibri_imx6/colibri_imx6.c
@@ -1091,7 +1091,7 @@
 	.use_dte = true,
 };
 
-U_BOOT_DEVICE(mxc_serial) = {
+U_BOOT_DRVINFO(mxc_serial) = {
 	.name = "serial_mxc",
 	.plat = &mxc_serial_plat,
 };
diff --git a/board/toradex/colibri_pxa270/colibri_pxa270.c b/board/toradex/colibri_pxa270/colibri_pxa270.c
index b9d0fb9..645751a 100644
--- a/board/toradex/colibri_pxa270/colibri_pxa270.c
+++ b/board/toradex/colibri_pxa270/colibri_pxa270.c
@@ -133,7 +133,7 @@
 	.base = (struct pxa_mmc_regs *)MMC0_BASE,
 };
 
-U_BOOT_DEVICE(pxa_mmcs) = {
+U_BOOT_DRVINFO(pxa_mmcs) = {
 	.name = "pxa_mmc",
 	.plat = &mmc_plat,
 };
@@ -146,7 +146,7 @@
 	.baudrate = CONFIG_BAUDRATE,
 };
 
-U_BOOT_DEVICE(pxa_serials) = {
+U_BOOT_DRVINFO(pxa_serials) = {
 	.name = "serial_pxa",
 	.plat = &serial_plat,
 };
diff --git a/doc/driver-model/design.rst b/doc/driver-model/design.rst
index f26e4f1..ffed7d5 100644
--- a/doc/driver-model/design.rst
+++ b/doc/driver-model/design.rst
@@ -422,7 +422,7 @@
 
 While plat is useful, a more flexible way of providing device data is
 by using device tree. In U-Boot you should use this where possible. Avoid
-sending patches which make use of the U_BOOT_DEVICE() macro unless strictly
+sending patches which make use of the U_BOOT_DRVINFO() macro unless strictly
 necessary.
 
 With device tree we replace the above code with the following device tree
@@ -436,7 +436,7 @@
 		sides = <4>;
 	};
 
-This means that instead of having lots of U_BOOT_DEVICE() declarations in
+This means that instead of having lots of U_BOOT_DRVINFO() declarations in
 the board file, we put these in the device tree. This approach allows a lot
 more generality, since the same board file can support many types of boards
 (e,g. with the same SoC) just by using different device trees. An added
@@ -665,9 +665,9 @@
 
 U-Boot discovers devices using one of these two methods:
 
-- Scan the U_BOOT_DEVICE() definitions. U-Boot looks up the name specified
+- Scan the U_BOOT_DRVINFO() definitions. U-Boot looks up the name specified
   by each, to find the appropriate U_BOOT_DRIVER() definition. In this case,
-  there is no path by which driver_data may be provided, but the U_BOOT_DEVICE()
+  there is no path by which driver_data may be provided, but the U_BOOT_DRVINFO()
   may provide plat.
 
 - Scan through the device tree definitions. U-Boot looks at top-level
@@ -685,7 +685,7 @@
 At this point all the devices are known, and bound to their drivers. There
 is a 'struct udevice' allocated for all devices. However, nothing has been
 activated (except for the root device). Each bound device that was created
-from a U_BOOT_DEVICE() declaration will hold the plat pointer specified
+from a U_BOOT_DRVINFO() declaration will hold the plat pointer specified
 in that declaration. For a bound device created from the device tree,
 plat will be NULL, but of_offset will be the offset of the device tree
 node that caused the device to be created. The uclass is set correctly for
@@ -726,7 +726,7 @@
    2. If plat_auto is non-zero, then the platform data space
    is allocated. This is only useful for device tree operation, since
    otherwise you would have to specific the platform data in the
-   U_BOOT_DEVICE() declaration. The space is allocated for the device and
+   U_BOOT_DRVINFO() declaration. The space is allocated for the device and
    zeroed. It will be accessible as dev->plat.
 
    3. If the device's uclass specifies a non-zero per_device_auto,
@@ -746,7 +746,7 @@
    do various calls like dev_read_u32(dev, ...) to access the node and store
    the resulting information into dev->plat. After this point, the device
    works the same way whether it was bound using a device tree node or
-   U_BOOT_DEVICE() structure. In either case, the platform data is now stored
+   U_BOOT_DRVINFO() structure. In either case, the platform data is now stored
    in the plat structure. Typically you will use the
    plat_auto feature to specify the size of the platform data
    structure, and U-Boot will automatically allocate and zero it for you before
@@ -855,7 +855,7 @@
    4. The device memory is freed (platform data, private data, uclass data,
    parent data).
 
-   Note: Because the platform data for a U_BOOT_DEVICE() is defined with a
+   Note: Because the platform data for a U_BOOT_DRVINFO() is defined with a
    static pointer, it is not de-allocated during the remove() method. For
    a device instantiated using the device tree data, the platform data will
    be dynamically allocated, and thus needs to be deallocated during the
@@ -931,7 +931,7 @@
 before relocation. While with DM_FLAG_PRE_RELOC flag of the driver all
 devices with the same driver are bound, which requires allocation a large
 amount of memory. When device tree is not used, DM_FLAG_PRE_RELOC is the
-only way for statically declared devices via U_BOOT_DEVICE() to be bound
+only way for statically declared devices via U_BOOT_DRVINFO() to be bound
 prior to relocation.
 
 It is possible to limit this to specific relocation steps, by using
diff --git a/doc/driver-model/of-plat.rst b/doc/driver-model/of-plat.rst
index afa27c2..39e6295 100644
--- a/doc/driver-model/of-plat.rst
+++ b/doc/driver-model/of-plat.rst
@@ -21,7 +21,7 @@
 case the overhead of device tree access may be too great.
 
 It is possible to create platform data manually by defining C structures
-for it, and reference that data in a U_BOOT_DEVICE() declaration. This
+for it, and reference that data in a U_BOOT_DRVINFO() declaration. This
 bypasses the use of device tree completely, effectively creating a parallel
 configuration mechanism. But it is an available option for SPL.
 
@@ -79,7 +79,7 @@
 
 A new tool called 'dtoc' converts a device tree file either into a set of
 struct declarations, one for each compatible node, and a set of
-U_BOOT_DEVICE() declarations along with the actual platform data for each
+U_BOOT_DRVINFO() declarations along with the actual platform data for each
 device. As an example, consider this MMC node:
 
 .. code-block:: none
@@ -155,7 +155,7 @@
             .card_detect_delay      = 0xc8,
     };
 
-    U_BOOT_DEVICE(dwmmc_at_ff0c0000) = {
+    U_BOOT_DRVINFO(dwmmc_at_ff0c0000) = {
             .name           = "rockchip_rk3288_dw_mshc",
             .plat       = &dtv_dwmmc_at_ff0c0000,
             .plat_size  = sizeof(dtv_dwmmc_at_ff0c0000),
@@ -178,7 +178,7 @@
 therefore do nothing in such a driver.
 
 Note that for the platform data to be matched with a driver, the 'name'
-property of the U_BOOT_DEVICE() declaration has to match a driver declared
+property of the U_BOOT_DRVINFO() declaration has to match a driver declared
 via U_BOOT_DRIVER(). This effectively means that a U_BOOT_DRIVER() with a
 'name' corresponding to the devicetree 'compatible' string (after converting
 it to a valid name for C) is needed, so a dedicated driver is required for
@@ -189,7 +189,7 @@
 This macro produces no code, but it is by dtoc tool.
 
 The parent_idx is the index of the parent driver_info structure within its
-linker list (instantiated by the U_BOOT_DEVICE() macro). This is used to support
+linker list (instantiated by the U_BOOT_DRVINFO() macro). This is used to support
 dev_get_parent(). The dm_populate_phandle_data() is included to allow for
 fix-ups required by dtoc. It is not currently used. The values in 'clocks' are
 the index of the driver_info for the target device followed by any phandle
@@ -339,7 +339,7 @@
 The dt-plat.c file contains the device declarations and is is built in
 spl/dt-plat.c. It additionally contains the definition of
 dm_populate_phandle_data() which is responsible of filling the phandle
-information by adding references to U_BOOT_DEVICE by using DM_GET_DEVICE
+information by adding references to U_BOOT_DRVINFO by using DM_GET_DEVICE
 
 The pylibfdt Python module is used to access the devicetree.
 
diff --git a/doc/driver-model/remoteproc-framework.rst b/doc/driver-model/remoteproc-framework.rst
index edb09cc..566495a 100644
--- a/doc/driver-model/remoteproc-framework.rst
+++ b/doc/driver-model/remoteproc-framework.rst
@@ -125,7 +125,7 @@
 		.driver_plat_data = &mydriver_data;
 	};
 
-	U_BOOT_DEVICE(proc_3_demo) = {
+	U_BOOT_DRVINFO(proc_3_demo) = {
 		.name = "sandbox_test_proc",
 		.plat = &proc_3_test,
 	};
diff --git a/doc/driver-model/spi-howto.rst b/doc/driver-model/spi-howto.rst
index f1c4167..97fbf75 100644
--- a/doc/driver-model/spi-howto.rst
+++ b/doc/driver-model/spi-howto.rst
@@ -270,7 +270,7 @@
 Add the platform data [non-device-tree only]
 --------------------------------------------
 
-Specify this data in a U_BOOT_DEVICE() declaration in your board file:
+Specify this data in a U_BOOT_DRVINFO() declaration in your board file:
 
 .. code-block:: c
 
@@ -281,7 +281,7 @@
 		.deactivate_delay_us = ...
 	};
 
-	U_BOOT_DEVICE(board_spi0) = {
+	U_BOOT_DRVINFO(board_spi0) = {
 		.name = "exynos_spi",
 		.plat = &platdata_spi0,
 	};
diff --git a/drivers/crypto/fsl/fsl_rsa.c b/drivers/crypto/fsl/fsl_rsa.c
index ed2a54f..897ee85 100644
--- a/drivers/crypto/fsl/fsl_rsa.c
+++ b/drivers/crypto/fsl/fsl_rsa.c
@@ -55,6 +55,6 @@
 	.ops	= &fsl_mod_exp_ops,
 };
 
-U_BOOT_DEVICE(fsl_rsa) = {
+U_BOOT_DRVINFO(fsl_rsa) = {
 	.name = "fsl_rsa_mod_exp",
 };
diff --git a/drivers/crypto/rsa_mod_exp/mod_exp_sw.c b/drivers/crypto/rsa_mod_exp/mod_exp_sw.c
index 4ce85b3..7bed444 100644
--- a/drivers/crypto/rsa_mod_exp/mod_exp_sw.c
+++ b/drivers/crypto/rsa_mod_exp/mod_exp_sw.c
@@ -35,6 +35,6 @@
 	.flags	= DM_FLAG_PRE_RELOC,
 };
 
-U_BOOT_DEVICE(mod_exp_sw) = {
+U_BOOT_DRVINFO(mod_exp_sw) = {
 	.name = "mod_exp_sw",
 };
diff --git a/drivers/demo/demo-pdata.c b/drivers/demo/demo-pdata.c
index b504c31..818f775 100644
--- a/drivers/demo/demo-pdata.c
+++ b/drivers/demo/demo-pdata.c
@@ -20,27 +20,27 @@
 	.sides = 6.
 };
 
-U_BOOT_DEVICE(demo0) = {
+U_BOOT_DRVINFO(demo0) = {
 	.name = "demo_shape_drv",
 	.plat = &red_square,
 };
 
-U_BOOT_DEVICE(demo1) = {
+U_BOOT_DRVINFO(demo1) = {
 	.name = "demo_simple_drv",
 	.plat = &red_square,
 };
 
-U_BOOT_DEVICE(demo2) = {
+U_BOOT_DRVINFO(demo2) = {
 	.name = "demo_shape_drv",
 	.plat = &green_triangle,
 };
 
-U_BOOT_DEVICE(demo3) = {
+U_BOOT_DRVINFO(demo3) = {
 	.name = "demo_simple_drv",
 	.plat = &yellow_hexagon,
 };
 
-U_BOOT_DEVICE(demo4) = {
+U_BOOT_DRVINFO(demo4) = {
 	.name = "demo_shape_drv",
 	.plat = &yellow_hexagon,
 };
diff --git a/drivers/gpio/imx_rgpio2p.c b/drivers/gpio/imx_rgpio2p.c
index a5a290a..0e2874c 100644
--- a/drivers/gpio/imx_rgpio2p.c
+++ b/drivers/gpio/imx_rgpio2p.c
@@ -158,7 +158,7 @@
 	/*
 	 * If plat already exsits, directly return.
 	 * Actually only when DT is not supported, plat
-	 * is statically initialized in U_BOOT_DEVICES.Here
+	 * is statically initialized in U_BOOT_DRVINFOS.Here
 	 * will return.
 	 */
 	if (plat)
@@ -216,7 +216,7 @@
 	{ 5, (struct gpio_regs *)RGPIO2P_GPIO6_BASE_ADDR },
 };
 
-U_BOOT_DEVICES(imx_rgpio2ps) = {
+U_BOOT_DRVINFOS(imx_rgpio2ps) = {
 	{ "imx_rgpio2p", &imx_plat[0] },
 	{ "imx_rgpio2p", &imx_plat[1] },
 	{ "imx_rgpio2p", &imx_plat[2] },
diff --git a/drivers/gpio/mxc_gpio.c b/drivers/gpio/mxc_gpio.c
index 9fc217a..6280fb5 100644
--- a/drivers/gpio/mxc_gpio.c
+++ b/drivers/gpio/mxc_gpio.c
@@ -372,7 +372,7 @@
 #endif
 };
 
-U_BOOT_DEVICES(mxc_gpios) = {
+U_BOOT_DRVINFOS(mxc_gpios) = {
 	{ "gpio_mxc", &mxc_plat[0] },
 	{ "gpio_mxc", &mxc_plat[1] },
 	{ "gpio_mxc", &mxc_plat[2] },
diff --git a/drivers/remoteproc/sandbox_testproc.c b/drivers/remoteproc/sandbox_testproc.c
index ee2ee73..6836eca 100644
--- a/drivers/remoteproc/sandbox_testproc.c
+++ b/drivers/remoteproc/sandbox_testproc.c
@@ -352,7 +352,7 @@
 	.mem_type = RPROC_INTERNAL_MEMORY_MAPPED,
 };
 
-U_BOOT_DEVICE(proc_3_demo) = {
+U_BOOT_DRVINFO(proc_3_demo) = {
 	.name = "sandbox_test_proc",
 	.plat = &proc_3_test,
 };
diff --git a/drivers/rtc/emul_rtc.c b/drivers/rtc/emul_rtc.c
index 1dc80ca..8f0e1ab 100644
--- a/drivers/rtc/emul_rtc.c
+++ b/drivers/rtc/emul_rtc.c
@@ -91,6 +91,6 @@
 	.priv_auto	= sizeof(struct emul_rtc),
 };
 
-U_BOOT_DEVICE(rtc_emul) = {
+U_BOOT_DRVINFO(rtc_emul) = {
 	.name	= "rtc_emul",
 };
diff --git a/drivers/serial/sandbox.c b/drivers/serial/sandbox.c
index 19368ba..756738c 100644
--- a/drivers/serial/sandbox.c
+++ b/drivers/serial/sandbox.c
@@ -241,7 +241,7 @@
 	.colour = -1,
 };
 
-U_BOOT_DEVICE(serial_sandbox_non_fdt) = {
+U_BOOT_DRVINFO(serial_sandbox_non_fdt) = {
 	.name = "sandbox_serial",
 	.plat = &platdata_non_fdt,
 };
diff --git a/drivers/sysreset/sysreset_sandbox.c b/drivers/sysreset/sysreset_sandbox.c
index 8eca7d8..0868582 100644
--- a/drivers/sysreset/sysreset_sandbox.c
+++ b/drivers/sysreset/sysreset_sandbox.c
@@ -47,7 +47,7 @@
 
 	/*
 	 * If we have a device tree, the device we created from platform data
-	 * (see the U_BOOT_DEVICE() declaration below) should not do anything.
+	 * (see the U_BOOT_DRVINFO() declaration below) should not do anything.
 	 * If we are that device, return an error.
 	 */
 	if (state->fdt_fname && !dev_has_ofnode(dev))
@@ -135,7 +135,7 @@
 
 #if !CONFIG_IS_ENABLED(OF_PLATDATA)
 /* This is here in case we don't have a device tree */
-U_BOOT_DEVICE(sysreset_sandbox_non_fdt) = {
+U_BOOT_DRVINFO(sysreset_sandbox_non_fdt) = {
 	.name = "sysreset_sandbox",
 };
 #endif
diff --git a/drivers/timer/sandbox_timer.c b/drivers/timer/sandbox_timer.c
index 135c0f3..2075cd4 100644
--- a/drivers/timer/sandbox_timer.c
+++ b/drivers/timer/sandbox_timer.c
@@ -65,6 +65,6 @@
 };
 
 /* This is here in case we don't have a device tree */
-U_BOOT_DEVICE(sandbox_timer_non_fdt) = {
+U_BOOT_DRVINFO(sandbox_timer_non_fdt) = {
 	.name = "sandbox_timer",
 };
diff --git a/drivers/video/sunxi/sunxi_de2.c b/drivers/video/sunxi/sunxi_de2.c
index 50657a7..a3e21aa 100644
--- a/drivers/video/sunxi/sunxi_de2.c
+++ b/drivers/video/sunxi/sunxi_de2.c
@@ -319,7 +319,7 @@
 	.flags	= DM_FLAG_PRE_RELOC,
 };
 
-U_BOOT_DEVICE(sunxi_de2) = {
+U_BOOT_DRVINFO(sunxi_de2) = {
 	.name = "sunxi_de2"
 };
 
diff --git a/drivers/video/sunxi/sunxi_dw_hdmi.c b/drivers/video/sunxi/sunxi_dw_hdmi.c
index 3e8d715..0b8cefc 100644
--- a/drivers/video/sunxi/sunxi_dw_hdmi.c
+++ b/drivers/video/sunxi/sunxi_dw_hdmi.c
@@ -398,6 +398,6 @@
 	.priv_auto	= sizeof(struct sunxi_dw_hdmi_priv),
 };
 
-U_BOOT_DEVICE(sunxi_dw_hdmi) = {
+U_BOOT_DRVINFO(sunxi_dw_hdmi) = {
 	.name = "sunxi_dw_hdmi"
 };
diff --git a/drivers/video/sunxi/sunxi_lcd.c b/drivers/video/sunxi/sunxi_lcd.c
index dd2bb1f..635edf6 100644
--- a/drivers/video/sunxi/sunxi_lcd.c
+++ b/drivers/video/sunxi/sunxi_lcd.c
@@ -146,7 +146,7 @@
 };
 
 #ifdef CONFIG_MACH_SUN50I
-U_BOOT_DEVICE(sunxi_lcd) = {
+U_BOOT_DRVINFO(sunxi_lcd) = {
 	.name = "sunxi_lcd"
 };
 #endif
diff --git a/dts/Kconfig b/dts/Kconfig
index aeda542..71f5055 100644
--- a/dts/Kconfig
+++ b/dts/Kconfig
@@ -346,13 +346,13 @@
 	  former can add 3KB or more to a Thumb 2 Image.
 
 	  This option enables generation of platform data from the device
-	  tree as C code. This code creates devices using U_BOOT_DEVICE()
+	  tree as C code. This code creates devices using U_BOOT_DRVINFO()
 	  declarations. The benefit is that it allows driver code to access
 	  the platform data directly in C structures, avoidin the libfdt
 	  overhead.
 
 	  This option works by generating C structure declarations for each
-	  compatible string, then adding platform data and U_BOOT_DEVICE
+	  compatible string, then adding platform data and U_BOOT_DRVINFO
 	  declarations for each node. See of-plat.txt for more information.
 
 config SPL_OF_PLATDATA_PARENT
@@ -376,13 +376,13 @@
 	  former can add 3KB or more to a Thumb 2 Image.
 
 	  This option enables generation of platform data from the device
-	  tree as C code. This code creates devices using U_BOOT_DEVICE()
+	  tree as C code. This code creates devices using U_BOOT_DRVINFO()
 	  declarations. The benefit is that it allows driver code to access
 	  the platform data directly in C structures, avoidin the libfdt
 	  overhead.
 
 	  This option works by generating C structure declarations for each
-	  compatible string, then adding platform data and U_BOOT_DEVICE
+	  compatible string, then adding platform data and U_BOOT_DRVINFO
 	  declarations for each node. See of-plat.txt for more information.
 
 config TPL_OF_PLATDATA_PARENT
diff --git a/include/dm/device.h b/include/dm/device.h
index 4469804..e16ba24 100644
--- a/include/dm/device.h
+++ b/include/dm/device.h
@@ -104,7 +104,7 @@
  * particular port or peripheral (essentially a driver instance).
  *
  * A device will come into existence through a 'bind' call, either due to
- * a U_BOOT_DEVICE() macro (in which case plat is non-NULL) or a node
+ * a U_BOOT_DRVINFO() macro (in which case plat is non-NULL) or a node
  * in the device tree (in which case of_offset is >= 0). In the latter case
  * we translate the device tree information into plat in a function
  * implemented by the driver of_to_plat method (called just before the
@@ -293,7 +293,7 @@
  * platform data to be allocated in the device's ->plat pointer.
  * This is typically only useful for device-tree-aware drivers (those with
  * an of_match), since drivers which use plat will have the data
- * provided in the U_BOOT_DEVICE() instantiation.
+ * provided in the U_BOOT_DRVINFO() instantiation.
  * @per_child_auto: Each device can hold private data owned by
  * its parent. If required this will be automatically allocated if this
  * value is non-zero.
diff --git a/include/dm/lists.h b/include/dm/lists.h
index 070bc9c..1a86552 100644
--- a/include/dm/lists.h
+++ b/include/dm/lists.h
@@ -35,7 +35,7 @@
 /**
  * lists_bind_drivers() - search for and bind all drivers to parent
  *
- * This searches the U_BOOT_DEVICE() structures and creates new devices for
+ * This searches the U_BOOT_DRVINFO() structures and creates new devices for
  * each one. The devices will have @parent as their parent.
  *
  * @parent: parent device (root)
diff --git a/include/dm/platdata.h b/include/dm/platdata.h
index d650fb3..e2b16ce 100644
--- a/include/dm/platdata.h
+++ b/include/dm/platdata.h
@@ -56,31 +56,31 @@
  * is not feasible (e.g. serial driver in SPL where <8KB of SRAM is
  * available). U-Boot's driver model uses device tree for configuration.
  *
- * When of-platdata is in use, U_BOOT_DEVICE() cannot be used outside of the
+ * When of-platdata is in use, U_BOOT_DRVINFO() cannot be used outside of the
  * dt-plat.c file created by dtoc
  */
 #if CONFIG_IS_ENABLED(OF_PLATDATA) && !defined(DT_PLATDATA_C)
-#define U_BOOT_DEVICE(__name)	_Static_assert(false, \
-	"Cannot use U_BOOT_DEVICE with of-platdata. Please use devicetree instead")
+#define U_BOOT_DRVINFO(__name)	_Static_assert(false, \
+	"Cannot use U_BOOT_DRVINFO with of-platdata. Please use devicetree instead")
 #else
-#define U_BOOT_DEVICE(__name)						\
+#define U_BOOT_DRVINFO(__name)						\
 	ll_entry_declare(struct driver_info, __name, driver_info)
 #endif
 
 /* Declare a list of devices. The argument is a driver_info[] array */
-#define U_BOOT_DEVICES(__name)						\
+#define U_BOOT_DRVINFOS(__name)						\
 	ll_entry_declare_list(struct driver_info, __name, driver_info)
 
 /**
  * Get a pointer to a given device info given its name
  *
- * With the declaration U_BOOT_DEVICE(name), DM_GET_DEVICE(name) will return a
+ * With the declaration U_BOOT_DRVINFO(name), DM_GET_DEVICE(name) will return a
  * pointer to the struct driver_info created by that declaration.
  *
  * if OF_PLATDATA is enabled, from this it is possible to use the @dev member of
  * struct driver_info to find the device pointer itself.
  *
- * TODO(sjg@chromium.org): U_BOOT_DEVICE() tells U-Boot to create a device, so
+ * TODO(sjg@chromium.org): U_BOOT_DRVINFO() tells U-Boot to create a device, so
  * the naming seems sensible, but DM_GET_DEVICE() is a bit of misnomer, since it
  * finds the driver_info record, not the device.
  *
@@ -93,7 +93,7 @@
 /**
  * dm_populate_phandle_data() - Populates phandle data in platda
  *
- * This populates phandle data with an U_BOOT_DEVICE entry get by
+ * This populates phandle data with an U_BOOT_DRVINFO entry get by
  * DM_GET_DEVICE. The implementation of this function will be done
  * by dtoc when parsing dtb.
  */
diff --git a/include/dm/platform_data/spi_pl022.h b/include/dm/platform_data/spi_pl022.h
index c5aa321..7f74b3c 100644
--- a/include/dm/platform_data/spi_pl022.h
+++ b/include/dm/platform_data/spi_pl022.h
@@ -3,7 +3,7 @@
  * (C) Copyright 2018
  * Quentin Schulz, Bootlin, quentin.schulz@bootlin.com
  *
- * Structure for use with U_BOOT_DEVICE for pl022 SPI devices or to use
+ * Structure for use with U_BOOT_DRVINFO for pl022 SPI devices or to use
  * in of_to_plat.
  */
 
diff --git a/test/dm/core.c b/test/dm/core.c
index 580d171..82b7a66 100644
--- a/test/dm/core.c
+++ b/test/dm/core.c
@@ -43,17 +43,17 @@
 	.ping_add		= TEST_INTVAL_PRE_RELOC,
 };
 
-U_BOOT_DEVICE(dm_test_info1) = {
+U_BOOT_DRVINFO(dm_test_info1) = {
 	.name = "test_drv",
 	.plat = &test_pdata[0],
 };
 
-U_BOOT_DEVICE(dm_test_info2) = {
+U_BOOT_DRVINFO(dm_test_info2) = {
 	.name = "test_drv",
 	.plat = &test_pdata[1],
 };
 
-U_BOOT_DEVICE(dm_test_info3) = {
+U_BOOT_DRVINFO(dm_test_info3) = {
 	.name = "test_drv",
 	.plat = &test_pdata[2],
 };
diff --git a/tools/dtoc/dtb_platdata.py b/tools/dtoc/dtb_platdata.py
index 7bd1989..ebe5132 100644
--- a/tools/dtoc/dtb_platdata.py
+++ b/tools/dtoc/dtb_platdata.py
@@ -713,14 +713,14 @@
     def _declare_device(self, var_name, struct_name, node_parent):
         """Add a device declaration to the output
 
-        This declares a U_BOOT_DEVICE() for the device being processed
+        This declares a U_BOOT_DRVINFO() for the device being processed
 
         Args:
             var_name (str): C name for the node
             struct_name (str): Name for the dt struct associated with the node
             node_parent (Node): Parent of the node (or None if none)
         """
-        self.buf('U_BOOT_DEVICE(%s) = {\n' % var_name)
+        self.buf('U_BOOT_DRVINFO(%s) = {\n' % var_name)
         self.buf('\t.name\t\t= "%s",\n' % struct_name)
         self.buf('\t.plat\t= &%s%s,\n' % (VAL_PREFIX, var_name))
         self.buf('\t.plat_size\t= sizeof(%s%s),\n' % (VAL_PREFIX, var_name))
@@ -783,14 +783,14 @@
         """Generate device defintions for the platform data
 
         This writes out C platform data initialisation data and
-        U_BOOT_DEVICE() declarations for each valid node. Where a node has
+        U_BOOT_DRVINFO() declarations for each valid node. Where a node has
         multiple compatible strings, a #define is used to make them equivalent.
 
         See the documentation in doc/driver-model/of-plat.rst for more
         information.
         """
         self.out_header()
-        self.out('/* Allow use of U_BOOT_DEVICE() in this file */\n')
+        self.out('/* Allow use of U_BOOT_DRVINFO() in this file */\n')
         self.out('#define DT_PLATDATA_C\n')
         self.out('\n')
         self.out('#include <common.h>\n')
diff --git a/tools/dtoc/test_dtoc.py b/tools/dtoc/test_dtoc.py
index fb65f28..dbd4e3b 100755
--- a/tools/dtoc/test_dtoc.py
+++ b/tools/dtoc/test_dtoc.py
@@ -44,7 +44,7 @@
  * This file was generated by dtoc from a .dtb (device tree binary) file.
  */
 
-/* Allow use of U_BOOT_DEVICE() in this file */
+/* Allow use of U_BOOT_DRVINFO() in this file */
 #define DT_PLATDATA_C
 
 #include <common.h>
@@ -214,7 +214,7 @@
 /* Node /i2c@0 index 0 */
 static struct dtd_sandbox_i2c_test dtv_i2c_at_0 = {
 };
-U_BOOT_DEVICE(i2c_at_0) = {
+U_BOOT_DRVINFO(i2c_at_0) = {
 \t.name\t\t= "sandbox_i2c_test",
 \t.plat\t= &dtv_i2c_at_0,
 \t.plat_size\t= sizeof(dtv_i2c_at_0),
@@ -226,7 +226,7 @@
 \t.low_power\t\t= true,
 \t.reg\t\t\t= {0x9, 0x0},
 };
-U_BOOT_DEVICE(pmic_at_9) = {
+U_BOOT_DRVINFO(pmic_at_9) = {
 \t.name\t\t= "sandbox_pmic_test",
 \t.plat\t= &dtv_pmic_at_9,
 \t.plat_size\t= sizeof(dtv_pmic_at_9),
@@ -246,7 +246,7 @@
 \t.stringarray\t\t= {"multi-word", "message", ""},
 \t.stringval\t\t= "message",
 };
-U_BOOT_DEVICE(spl_test) = {
+U_BOOT_DRVINFO(spl_test) = {
 \t.name\t\t= "sandbox_spl_test",
 \t.plat\t= &dtv_spl_test,
 \t.plat_size\t= sizeof(dtv_spl_test),
@@ -265,7 +265,7 @@
 \t.stringarray\t\t= {"another", "multi-word", "message"},
 \t.stringval\t\t= "message2",
 };
-U_BOOT_DEVICE(spl_test2) = {
+U_BOOT_DRVINFO(spl_test2) = {
 \t.name\t\t= "sandbox_spl_test",
 \t.plat\t= &dtv_spl_test2,
 \t.plat_size\t= sizeof(dtv_spl_test2),
@@ -278,7 +278,7 @@
 \t\t0x0},
 \t.stringarray\t\t= {"one", "", ""},
 };
-U_BOOT_DEVICE(spl_test3) = {
+U_BOOT_DRVINFO(spl_test3) = {
 \t.name\t\t= "sandbox_spl_test",
 \t.plat\t= &dtv_spl_test3,
 \t.plat_size\t= sizeof(dtv_spl_test3),
@@ -333,7 +333,7 @@
 \t.gpio_controller\t= true,
 \t.sandbox_gpio_count\t= 0x14,
 };
-U_BOOT_DEVICE(gpios_at_0) = {
+U_BOOT_DRVINFO(gpios_at_0) = {
 \t.name\t\t= "sandbox_gpio",
 \t.plat\t= &dtv_gpios_at_0,
 \t.plat_size\t= sizeof(dtv_gpios_at_0),
@@ -365,7 +365,7 @@
 /* Node /spl-test index 0 */
 static struct dtd_invalid dtv_spl_test = {
 };
-U_BOOT_DEVICE(spl_test) = {
+U_BOOT_DRVINFO(spl_test) = {
 \t.name\t\t= "invalid",
 \t.plat\t= &dtv_spl_test,
 \t.plat_size\t= sizeof(dtv_spl_test),
@@ -400,7 +400,7 @@
 static struct dtd_target dtv_phandle2_target = {
 \t.intval\t\t\t= 0x1,
 };
-U_BOOT_DEVICE(phandle2_target) = {
+U_BOOT_DRVINFO(phandle2_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle2_target,
 \t.plat_size\t= sizeof(dtv_phandle2_target),
@@ -411,7 +411,7 @@
 static struct dtd_target dtv_phandle3_target = {
 \t.intval\t\t\t= 0x2,
 };
-U_BOOT_DEVICE(phandle3_target) = {
+U_BOOT_DRVINFO(phandle3_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle3_target,
 \t.plat_size\t= sizeof(dtv_phandle3_target),
@@ -422,7 +422,7 @@
 static struct dtd_target dtv_phandle_target = {
 \t.intval\t\t\t= 0x0,
 };
-U_BOOT_DEVICE(phandle_target) = {
+U_BOOT_DRVINFO(phandle_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle_target,
 \t.plat_size\t= sizeof(dtv_phandle_target),
@@ -437,7 +437,7 @@
 \t\t\t{1, {12, 13}},
 \t\t\t{4, {}},},
 };
-U_BOOT_DEVICE(phandle_source) = {
+U_BOOT_DRVINFO(phandle_source) = {
 \t.name\t\t= "source",
 \t.plat\t= &dtv_phandle_source,
 \t.plat_size\t= sizeof(dtv_phandle_source),
@@ -449,7 +449,7 @@
 \t.clocks\t\t\t= {
 \t\t\t{4, {}},},
 };
-U_BOOT_DEVICE(phandle_source2) = {
+U_BOOT_DRVINFO(phandle_source2) = {
 \t.name\t\t= "source",
 \t.plat\t= &dtv_phandle_source2,
 \t.plat_size\t= sizeof(dtv_phandle_source2),
@@ -487,7 +487,7 @@
 /* Node /phandle-target index 1 */
 static struct dtd_target dtv_phandle_target = {
 };
-U_BOOT_DEVICE(phandle_target) = {
+U_BOOT_DRVINFO(phandle_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle_target,
 \t.plat_size\t= sizeof(dtv_phandle_target),
@@ -499,7 +499,7 @@
 \t.clocks\t\t\t= {
 \t\t\t{1, {}},},
 };
-U_BOOT_DEVICE(phandle_source2) = {
+U_BOOT_DRVINFO(phandle_source2) = {
 \t.name\t\t= "source",
 \t.plat\t= &dtv_phandle_source2,
 \t.plat_size\t= sizeof(dtv_phandle_source2),
@@ -522,7 +522,7 @@
 static struct dtd_target dtv_phandle2_target = {
 \t.intval\t\t\t= 0x1,
 };
-U_BOOT_DEVICE(phandle2_target) = {
+U_BOOT_DRVINFO(phandle2_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle2_target,
 \t.plat_size\t= sizeof(dtv_phandle2_target),
@@ -533,7 +533,7 @@
 static struct dtd_target dtv_phandle3_target = {
 \t.intval\t\t\t= 0x2,
 };
-U_BOOT_DEVICE(phandle3_target) = {
+U_BOOT_DRVINFO(phandle3_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle3_target,
 \t.plat_size\t= sizeof(dtv_phandle3_target),
@@ -544,7 +544,7 @@
 static struct dtd_target dtv_phandle_target = {
 \t.intval\t\t\t= 0x0,
 };
-U_BOOT_DEVICE(phandle_target) = {
+U_BOOT_DRVINFO(phandle_target) = {
 \t.name\t\t= "target",
 \t.plat\t= &dtv_phandle_target,
 \t.plat_size\t= sizeof(dtv_phandle_target),
@@ -559,7 +559,7 @@
 \t\t\t{1, {12, 13}},
 \t\t\t{4, {}},},
 };
-U_BOOT_DEVICE(phandle_source) = {
+U_BOOT_DRVINFO(phandle_source) = {
 \t.name\t\t= "source",
 \t.plat\t= &dtv_phandle_source,
 \t.plat_size\t= sizeof(dtv_phandle_source),
@@ -571,7 +571,7 @@
 \t.cd_gpios\t\t= {
 \t\t\t{4, {}},},
 };
-U_BOOT_DEVICE(phandle_source2) = {
+U_BOOT_DRVINFO(phandle_source2) = {
 \t.name\t\t= "source",
 \t.plat\t= &dtv_phandle_source2,
 \t.plat_size\t= sizeof(dtv_phandle_source2),
@@ -629,7 +629,7 @@
 static struct dtd_test1 dtv_test1 = {
 \t.reg\t\t\t= {0x1234, 0x5678},
 };
-U_BOOT_DEVICE(test1) = {
+U_BOOT_DRVINFO(test1) = {
 \t.name\t\t= "test1",
 \t.plat\t= &dtv_test1,
 \t.plat_size\t= sizeof(dtv_test1),
@@ -640,7 +640,7 @@
 static struct dtd_test2 dtv_test2 = {
 \t.reg\t\t\t= {0x1234567890123456, 0x9876543210987654},
 };
-U_BOOT_DEVICE(test2) = {
+U_BOOT_DRVINFO(test2) = {
 \t.name\t\t= "test2",
 \t.plat\t= &dtv_test2,
 \t.plat_size\t= sizeof(dtv_test2),
@@ -651,7 +651,7 @@
 static struct dtd_test3 dtv_test3 = {
 \t.reg\t\t\t= {0x1234567890123456, 0x9876543210987654, 0x2, 0x3},
 };
-U_BOOT_DEVICE(test3) = {
+U_BOOT_DRVINFO(test3) = {
 \t.name\t\t= "test3",
 \t.plat\t= &dtv_test3,
 \t.plat_size\t= sizeof(dtv_test3),
@@ -684,7 +684,7 @@
 static struct dtd_test1 dtv_test1 = {
 \t.reg\t\t\t= {0x1234, 0x5678},
 };
-U_BOOT_DEVICE(test1) = {
+U_BOOT_DRVINFO(test1) = {
 \t.name\t\t= "test1",
 \t.plat\t= &dtv_test1,
 \t.plat_size\t= sizeof(dtv_test1),
@@ -695,7 +695,7 @@
 static struct dtd_test2 dtv_test2 = {
 \t.reg\t\t\t= {0x12345678, 0x98765432, 0x2, 0x3},
 };
-U_BOOT_DEVICE(test2) = {
+U_BOOT_DRVINFO(test2) = {
 \t.name\t\t= "test2",
 \t.plat\t= &dtv_test2,
 \t.plat_size\t= sizeof(dtv_test2),
@@ -731,7 +731,7 @@
 static struct dtd_test1 dtv_test1 = {
 \t.reg\t\t\t= {0x123400000000, 0x5678},
 };
-U_BOOT_DEVICE(test1) = {
+U_BOOT_DRVINFO(test1) = {
 \t.name\t\t= "test1",
 \t.plat\t= &dtv_test1,
 \t.plat_size\t= sizeof(dtv_test1),
@@ -742,7 +742,7 @@
 static struct dtd_test2 dtv_test2 = {
 \t.reg\t\t\t= {0x1234567890123456, 0x98765432},
 };
-U_BOOT_DEVICE(test2) = {
+U_BOOT_DRVINFO(test2) = {
 \t.name\t\t= "test2",
 \t.plat\t= &dtv_test2,
 \t.plat_size\t= sizeof(dtv_test2),
@@ -753,7 +753,7 @@
 static struct dtd_test3 dtv_test3 = {
 \t.reg\t\t\t= {0x1234567890123456, 0x98765432, 0x2, 0x3},
 };
-U_BOOT_DEVICE(test3) = {
+U_BOOT_DRVINFO(test3) = {
 \t.name\t\t= "test3",
 \t.plat\t= &dtv_test3,
 \t.plat_size\t= sizeof(dtv_test3),
@@ -789,7 +789,7 @@
 static struct dtd_test1 dtv_test1 = {
 \t.reg\t\t\t= {0x1234, 0x567800000000},
 };
-U_BOOT_DEVICE(test1) = {
+U_BOOT_DRVINFO(test1) = {
 \t.name\t\t= "test1",
 \t.plat\t= &dtv_test1,
 \t.plat_size\t= sizeof(dtv_test1),
@@ -800,7 +800,7 @@
 static struct dtd_test2 dtv_test2 = {
 \t.reg\t\t\t= {0x12345678, 0x9876543210987654},
 };
-U_BOOT_DEVICE(test2) = {
+U_BOOT_DRVINFO(test2) = {
 \t.name\t\t= "test2",
 \t.plat\t= &dtv_test2,
 \t.plat_size\t= sizeof(dtv_test2),
@@ -811,7 +811,7 @@
 static struct dtd_test3 dtv_test3 = {
 \t.reg\t\t\t= {0x12345678, 0x9876543210987654, 0x2, 0x3},
 };
-U_BOOT_DEVICE(test3) = {
+U_BOOT_DRVINFO(test3) = {
 \t.name\t\t= "test3",
 \t.plat\t= &dtv_test3,
 \t.plat_size\t= sizeof(dtv_test3),
@@ -863,7 +863,7 @@
 static struct dtd_sandbox_spl_test dtv_spl_test = {
 \t.intval\t\t\t= 0x1,
 };
-U_BOOT_DEVICE(spl_test) = {
+U_BOOT_DRVINFO(spl_test) = {
 \t.name\t\t= "sandbox_spl_test",
 \t.plat\t= &dtv_spl_test,
 \t.plat_size\t= sizeof(dtv_spl_test),
@@ -874,7 +874,7 @@
 static struct dtd_sandbox_spl_test dtv_spl_test2 = {
 \t.intarray\t\t= 0x5,
 };
-U_BOOT_DEVICE(spl_test2) = {
+U_BOOT_DRVINFO(spl_test2) = {
 \t.name\t\t= "sandbox_spl_test",
 \t.plat\t= &dtv_spl_test2,
 \t.plat_size\t= sizeof(dtv_spl_test2),